Tile Adhesives

Approx. Rs 45 / sq ftGet Latest Price

Product BrochureService Details:

DESCRIPTION
 Krystol T1 & T2 contains Krystol technology. When applied to concrete, Krystol chemically reacts with water and un-hydrated cement particles to form insoluble needle-shaped crystals that fill capillary pores and micro-cracks in the concrete and block the pathways for water and waterborne contaminants. Any moisture introduced over the lifespan of the concrete will initiate crystallization, ensuring permanent waterproofing protection.

FEATURES & BENEFITS  Replaces unreliable exterior membranes, liners and coatings
 Reaches well below the surface and is not affected by surface wear or abrasion
 Self-seals hairline cracks up to 0.5 mm (0.02 in.)
 Reactivates in the presence of moisture
 Effective against hydrostatic pressure up to 140 m (460 ft.) of head pressure
 Waterproofing increases with time
 Waterproofs from any direction (i.e. positive or negative side)
 Treatment may be applied to old or new concrete
 Safe for contact with potable water, certified by NSF to NSF/ANSI Standard 61
 Permanently waterproofs the concrete

APPLICATION 

STEP 1: SURFACE PREPARATION
1. Stop all leaks and repair all concrete defects such as cracks, faulty construction joints, pipe penetrations and honeycombing using the following repair procedures: a. Repair Application Instruction 5.12 - Waterproofing Cracks, Holes & Joints b. Repair Application Instruction 5.21 - Patching and Parging Defective Concrete and Masonry c. Repair Application Instruction 5.32 - Waterproofing Pipe Penetrations Prepare the surface by high pressure water blasting (minimum 3,000 psi), scarifying, shot blasting or sandblasting. Concrete surfaces must be clean and free of paint, sealers, form release agents, dirt, laitance or any other contaminates. The concrete must be open-pore and absorptive such that water placed on the surface will soak in. NOTE: Acid etching is not recommended. If acid etching must be used, all traces of acid must neutralized and rinsed away before applying the Krystol T1. 

STEP 2: MIXING Krystol T1 can be applied by a concrete brush, broom, texture sprayer or a grout pump/sprayer in either one or two coats. Mix ratios may slightly vary dependent on application method. Start by mixing approximately 3.5 parts of powder with 1 part clean water by volume and mix until smooth. Adjust as needed based on ambient temperatures to produce a thick, low-sag but spreadable coating. Krystol T1 will thicken in the pail when at rest. Stir as needed to maintain workability (do not add more water). Do not mix more material than can be applied in 20 minutes. 


STEP 3: APPLICATION Ensure that Krystol T1 is only applied to saturated-surface-dry (SSD) surface. As you apply the coating, you may need to rewet the concrete ahead of you to maintain a SSD surface. Failure to bring the surface to an SSD condition will result in a weak bond between the Krystol T1 coating and the concrete, and may lead to dusting, flaking and delamination. 1. Brush or spray Krystol T1 evenly over the concrete at a rate of 1.2 – 1.6 kg/m2 (2.2 – 3 lb/yd2) which can be applied in one or two coats. IMPORTANT: Set pails out over the work area in advance to help determine and track coverage. 2. With a concrete brush, scrub and brush the coating to low spots and ensure a good bond. 3. Finish with a lighter pressure to level high spots to ensure a uniform build with no thin spots. 4. If using two coats it is preferable to apply the second coat within 48 hours after the first coat has set hard (usually 6-24 hours depending on temperature). Wash and rinse the hardened Krystol T1 to remove surface bloom before applying the second coat. This may expose some of the aggregate in the first coat. Ensure the hardened Krystol T1 is in an SSD condition.

Approx. Rs 536 / BagGet Latest Price

Product BrochureService Details:

DescriptionUltraTech TILEFIXO-NT is a polymer modified cement based high performance, high strength, and high quality tile adhesivedeveloped to fix large size tiles/slabs of granite, marble, stones. Suitable for both internal and external, thin bed applications.SpecificationTechnical Parameters complies with IS 15477, EN 1348.Areas of ApplicationUltraTech TILEFIXO-NT is recommended for fixing large size tiles/slabs of granite, marble, stone wall cladding and flooring.It can be used over cementitious substrates only.● Prepare the surfaces before the Tile adhesive application by removing oil, bond inhibiting agents, dirt,dust and laitance. The cleaning can be carried out with suitable methods like by using wire brush, waterjetting, mopping, etc.● UltraTech BASEKRETE is recommended over vertical surfaces and UltraTech FLOORKRETE forhorizontal floor areas to level the surface in case of higher undulations or for any repair works toattain the flat, stable and normal absorption background prior to UltraTech TILEFIXO-NT application● UltraTech TILEFIXO-NT requires 25% of water by weight of material (4 parts of tile adhesive and 1part water)● Mix UltraTech TILEFIXO-NT to the measures quantity of water using mechanical stirring for 2-3minutes to ensure a consistency free of lumps● Allow to stand for 2 minutes for the mix to mature and then remix to use● Do not add any extra water to alter the mix consistency or to extend the pot life. Further wateradditions will hamper the adhesion strength of the Tile Adhesive● Apply the mixed UltraTech TILEFIXO-NT to the prepared substrate using the appropriate notchedtrowels for the size of the tiles being laid● A minimum of 6 mm bed thickness of Tile Adhesive for walls and floors must be achieved● Lay tiles onto the adhesive, firmly press the tile on to the adhesive to ensure good initial bonding, anddo not disturb tiles until the adhesive has set● No pre-wetting of tiles is required while using UltraTech TILEFIXO-NT● It is recommended to fix the tiles within 30 minutes of spreading of UltraTech TILEFIXO-NT toachieve the adequate bonding as per the Technical data provided● Any tile fixing after 30 minutes will lead to improper adhesion and may result in de-bonding of tiles● For vertical area applications, tiling should start from bottom to top● For tile-on-tile, tile-on-mosaic, tile-on-old cement floor application, care should be taken to preparethe existing base with adequate interlocking friction effect by removing polish/ wax/ top smooth layers

Approx. Rs 210 / KgGet Latest Price

Product BrochureService Details:

Description: ADH-EXPON is a high strength thixotropic adhesive used in construction joint sealing system. It is two component epoxy modified which consists of part A base and part B hardener. Mix two components thoroughly in given proportion and apply on prepared surface. It can also be used in repairing system like bedding mortar, non-sag concrete repair mortar. Uses:  Tunnels and culverts  Hydroelectric power plants  Sewage treatment plants  Roof joints  Basements  Water retaining structures  Joints between rigid and flexible surfaces  Around iron, steel and cement pipes  Repairing surface defects in concrete in horizontal, vertical and overhead applications  Fining of injection ports for Master Inject resins  Bonding of dowels, bolts and anchors into concrete  Rapid structural repair of concrete  Repair of concrete posts in situ Advantages:  Ease in site mixing  Low VOC makes it eco friendly  Ease in application  High resistance to chemical resistance  Highly adhesive to W-EXPON belt  High resistance to aggressive environment  Highly durable  Wide range of application  Adheres to concrete surfaces allows rapid repair of concrete Compliance standards: ASTM C881 Type 1 Grade 3 Class B & C Method of application:  Clean all the surface which is to be treated from dust, oil, laitance and cut back concrete to sound substrate.  Remove all type of curing compound, waterproofing membrane from conventional concrete surface.  Prime the surface if necessary with BUTABOND SBR mixed with cement. Priming the surface with BUTABOND SBR before application will provide better adhesion to the substrate and increase durability of the system.  Mix the pack of part A and part B properly which is supplied in pre weight quantity.  Apply the mix evenly with the help of trowel or spatula on the prepared surface.  Subsequent coats should be placed within 30-45 minutes and the ADH-EXPON should still be tacky.  Recoating time should be kept at least 8 hours. Curing: Cure time will depend on ambient condition generally cures in 7 days @ 230C. Coverage: 2 kg/m2 @1mm thickness. 

Approx. Rs 910 / BagGet Latest Price

Product BrochureService Details:

Kerabond Plus is a C2E class cementitious (C), improved (2), extended open time (E) adhesive.
CLASSIFICATION IN COMPLIANCE WITH IS 15477: 2019
Kerabond Plus is a high performance cementitious adhesive of Type 2.
WHERE TO USE
Bonding all types of ceramic tiles (porcelain, single-fired, terracotta, double-fired, klinker, etc.) vitrified tiles, natural stone and mosaics on internal walls and floors, and external floors. Also suitable for spot bonding insulating materials such as foam polystyrene, foam polyurethane, rock wool, glass wool, soundproofing panels, etc. Some application examples Bonding ceramic tiles, vitrified tiles, stone (if stable in damp environments) and mosaics on the following types of substrate: · walls with natural finish render or cementitious mortar; · internal cellular cement block walls; · gypsum and anhydrite primed with Primer G or Eco Prim T Plus; · plasterboard; · heated floors; · well cured, dry cementitious screeds and screeds made from special binders (such as Topcem ).
TECHNICAL CHARACTERISTICS
Kerabond Plus is a grey or white-coloured powder made from cement, selected graded sand, synthetic resin and special additives according to a formula developed in the MAPEI research laboratories. When mixed with water, it forms mortar with the following characteristics: · good workability; · perfect adhesion to all materials normally used in the building industry; · hardens with very little shrinkage. N.B.: When Kerabond Plus is mixed with Isolastic instead of water, its characteristics are improved to meet the requirements of class C2ES2 adhesive (highly deformable, improved cementitious adhesive with extended open time) according to ISO 13007 - 1.

Product BrochureService Details:

Mapelastic Smart is used for waterproofing hydraulic projects such as channels, faces of dams, swimming pools, basins, storage tanks, etc. and balconies and terraces. Particularly suitable for waterproofing irregular surfaces. Mapelastic Smart is also used to protect concrete structures, renders with hairline cracks and cementitious surfaces in general which, being subject to vibrations, may suffer from cracking. Some application examples · Waterproofing hydraulic channels, concrete water tanks, faces of dams and basins, including those containing potable water. · Waterproofing bathrooms, showers, balconies, terraces, swimming pools etc. before laying ceramic tiles. · Waterproofing plasterboard, render or cementitious surfaces, lightweight cement blocks and marine-grade plywood. · Flexible protection layer of new concrete structures or repaired structures subject to minor deformation under load. · Protection of cementitious renders or concrete with cracks due to shrinkage, minor movement caused by thermal gradients or dynamic stresses due to the passage of vehicles, against infiltration of water and aggressive elements from the atmosphere. · Protection of concrete pillars and beams and road and railway viaducts repaired with products from the Mapegrout or Planitop ranges against the penetration of carbon dioxide. · Protection of concrete surfaces which may come into contact with sea water, de-icing salts, such as sodium or calcium chloride, and sulphates.

Approx. Rs 800 / BagGet Latest Price

Product BrochureService Details:

Keraflex Maxi S1 is a deformable (S1), improved (2) slip-resistant (T) cementitious adhesive (C) with extended open time (E) of class C2TES1. Conformity of Keraflex Maxi S1 is declared in ITT certificate n° 25070387/Gi (TUM) and 25080246/Gi (TUM) issued by the Technische Universität München laboratory (Germany).
Keraflex Maxi S1 is a grey or white powder composed of cement and fine-graded sands. It contains a high quantity of synthetic resins and special additives according to a formulation developed in MAPEI’s Research & Development KERAFLEX MAXI S1 High performance, deformable Cementitious adhesive with extended open time and no vertical slip, for ceramic and vitrified tiles and stone material, also suitable for the installation of large-size vitrified tiles and natural stone laboratories. A mortar with the following features is obtained when Keraflex Maxi S1 is mixed with water: · low viscosity, therefore easily workable; · highly thixotropic: Keraflex Maxi S1 can be applied on a vertical surface without slumping or letting even heavy and large tiles slip. Tiles can be installed from the top towards the bottom without using spacer pegs; · good capability to accomodate the different deformation of the covering from the substrate. · perfect adherence to all materials normally used in building; · hardens, even when very thickly applied, without decreasing in thickness, until acquiring a considerable resistance. · particularly extended open and adjustability time, facilitating installation

Approx. Rs 4,555 / KgGet Latest Price

Product BrochureService Details:

Geotextiles are versatile permeable fabrics that, when used in conjunction with soil, can effectively perform multiple functions, including separation, filtration, reinforcement, protection, and drainage.

Approx. Rs 745 / BagGet Latest Price

Product BrochureService Details:

Product Description1. Ideal for walls 2. Polymer-modified 3. Thicknesses up to 15 mm 4. Ideal for wet areas 5. No sag 6. Very low voc 7. For glass mosaic 8. Prolonged workability 9. Adjustable

Areas of application Intended use: Surfaces: - Cement-based screeds and mortars - Cement-based plasters/renders - Cellular concrete, for internal use -
Waterproofing products - Concrete surfaces - Biocem based dry screeds - Cement-based self-levelling products -
Mortar modified with Aquastop P6 Materials: - Ceramic tiles - Vitrified tiles - Terracotta - Marble and natural stone - Various mosaics - Internal insulating and soundproofing panels Uses: - Floors and walls - For internal use - external - Domestic applications - Commercial applications - Street furniture

Approx. Rs 900 / BagGet Latest Price

Product BrochureService Details:

Product Description1. Ideal for walls 2. Polymer-modified 3. Thicknesses up to 15 mm 4. Ideal for wet areas 5. No sag 6. Very low voc 7. For glass mosaic 8. Prolonged workability 9. Adjustable

Areas of application Intended use: Surfaces: - Cement-based screeds and mortars - Cement-based plasters/renders - Cellular concrete, for internal use -
Waterproofing products - Concrete surfaces - Biocem based dry screeds - Cement-based self-levelling products -
Mortar modified with Aquastop P6 Materials: - Ceramic tiles - Vitrified tiles - Terracotta - Marble and natural stone - Various mosaics - Internal insulating and soundproofing panels Uses: - Floors and walls - For internal use - external - Domestic applications - Commercial applications - Street furniture

Approx. Rs 1,250 / BagGet Latest Price

Product BrochureService Details:

Product Description

USES:
Flexible mineral adhesive to fix vitrified tiles and Natural stones on floor and wall.

 Features and Advantages:

·         Highly polymer-modified

·         For internal and external use

·         For Balconies and Terraces

·         No sag

·         Prolonged workability

·         Adjustable

·         Sustains heat ageing

·         For fixing stones

 AREA OF USES :

 

Approx. Rs 800 / BagGet Latest Price

Product BrochureService Details:

Kerabond Plus is a C2E class cementitious (C), improved (2), extended open time (E) adhesive.
CLASSIFICATION IN COMPLIANCE WITH IS 15477: 2019
Kerabond Plus is a high performance cementitious adhesive of Type 2.
WHERE TO USE
Bonding all types of ceramic tiles (porcelain, single-fired, terracotta, double-fired, klinker, etc.) vitrified tiles, natural stone and mosaics on internal walls and floors, and external floors. Also suitable for spot bonding insulating materials such as foam polystyrene, foam polyurethane, rock wool, glass wool, soundproofing panels, etc. Some application examples Bonding ceramic tiles, vitrified tiles, stone (if stable in damp environments) and mosaics on the following types of substrate: · walls with natural finish render or cementitious mortar; · internal cellular cement block walls; · gypsum and anhydrite primed with Primer G or Eco Prim T Plus; · plasterboard; · heated floors; · well cured, dry cementitious screeds and screeds made from special binders (such as Topcem ).
TECHNICAL CHARACTERISTICS
Kerabond Plus is a grey or white-coloured powder made from cement, selected graded sand, synthetic resin and special additives according to a formula developed in the MAPEI research laboratories. When mixed with water, it forms mortar with the following characteristics: · good workability; · perfect adhesion to all materials normally used in the building industry; · hardens with very little shrinkage. N.B.: When Kerabond Plus is mixed with Isolastic instead of water, its characteristics are improved to meet the requirements of class C2ES2 adhesive (highly deformable, improved cementitious adhesive with extended open time) according to ISO 13007 - 1.

Approx. Rs 390 / BagGet Latest Price

Product BrochureService Details:

Description:
TERATILE GP a high quality adhesive for the permanent fixing of ceramic & small size of vitrified tiles for vertical and horizontal applications. It is also suitable for use in damp and totally submerged conditions. TERATILE GP tile adhesive is more suitable for internal applications.

Uses:
- Ceramic external application, Vitrified internal application, Porcelain & porous stones
- Permanent fixing of tiles over smooth surfaces
-  For specialized applications such as tile on tile and tile-on-glass etc.
- Applicable of tiles size 250mmX400mm,300mX3400mm,300mmX600mm,300mmX900mm 300mmX300mm - For tile & stone adhesive selection     www.redwop.net

Advantages:

- Polymer modified  
- Excellent adhesion on smooth surfaces  
- Forms a dense and impermeable mortar bed
- Self-cure  

 Substrate:  
- RCC, cement sheet, Plaster, AAC blocks, tile on tile, stone

Description: TERATILE GP a high quality adhesive for the permanent fixing of ceramic & small size of vitrified tiles for vertical and horizontal applications. It is also suitable for use in damp and totally submerged conditions. TERATILE GP tile adhesive is more suitable for internal applications. Uses:  Ceramic external application, Vitrified internal application, Porcelain & porous stones  Permanent fixing of tiles over smooth surfaces  For specialized applications such as tile on tile and tile-on-glass etc.  Applicable of tiles size 250mmX400mm,300mX3400mm,300mmX600mm,300mmX900mm 300mmX300mm  For tile & stone adhesive selection   Advantages:  Polymer modified  Excellent adhesion on smooth surfaces  Forms a dense and impermeable mortarbed  Self-cure Substrate: RCC, cement sheet, Plaster, AAC blocks, tile on tile, stone Compliance standard: IS 15477:2019, EN 12004 Method of application:  Clean the surface from efflorescence, laitance, dirt and other loose material than sprinkle water over the dry surface to make it wet.  Clean the back side of the tiles surface by using wire brush than wash it with ample amount of water until dryness is removed.  Add 20 kg of tile adhesive powder into 3.6 liter of water in a bucket and blend properly with electric blender.  Apply prepared paste as per requirement on both the tile surface and floor/wall surface.  Comb the adhesive paste to provide sufficient grip between the surface and tile

Download Links :